Vandtårnsvej 77
DK-2860 Søborg

+45 2856 3632

i

info@ps2u.dk

Competencies

Calibration

Calibration is the determination of a measuring instrument’s display error. Calibration is performed by a comparison with an accredited calibrated reference instrument. Process Support has equipment to perform traceable calibrations in many different areas.

 

Temperature
  • We calibrate in the range -93 to +310° C
  • We use dry block and/or liquid bath depending on the nature of the task
Pressure
  • We calibrate in the range of 0,02 to 20,5 BarA and -0,98 to 20,5 Barg
  • We can calibrate differential pressure in the range -1000 to +1000 Pa
Humidity
  • Vi kalibrerer i området 10 til 95 %RH (10 til 40°C)
  • We can also perform calibration of a loop (0 to 100%RH)
Electrical
  • We calibrate from 4 to 20 mA, if you divide the measured circuit during the calibration
    • In connection with ATEX zones
    • To minimize contamination in the room
Flow
  • We calibrate in the range 600 to 4500 L/h

 

Light / Lux
  • Vi kalibrerer i området 50,0 til 1790 Lux
Dosage / Load cells
  • We calibrate in the range 600 to 4500 kg/hr
  • Load cells can be calibrated starting at 1 kg →
Conductivity
  • Vi kalibrerer i området 0,05 – 1457 µS/cm
  • Vi kalibrerer i området 1,4 til 400 mS/cm
Time
  • We calibrate in the range 0 to 3899 seconds

Thermal Validation

Thermal validation is the customer’s guarantee that the various thermal processes are under control, that they work consistently based on the predetermined specifications and comply with the requirements. If a tendency in the validations is observed it can the be determined whether there is variation between the repeated validations. The variation can give an indication of a change in the process, the environment, the handling, utility variations or a mechanical fault.

Autoclave qualification
  • We work with re-programming of autoclaves
  • Cycle development and changes on autoclaves followed by initial validation
  • Copying and transferring existing programs

 

    Autoclave validation
    • We have experience in validating large and small autoclaves; 10L to > >800L autoklaves. These can be anything from top-operated table autoclaves to large chamber autoclaves with double doors. We can also assist in obtaining Biological Indicators both ampoules and strips.
    • We use the Kaye Validator 2000

     

       

        Biological indicator
        • F0 – value calculations
        • Bioburden, Overkill Half Cycle Approach and Partial Cycle Approach
        • D-value calculations

         

          Dry sterilizer
          • We have experience with validation of dry sterilizers between 50L to >800L. We can also assist in obtaining Biological Indicators.
          • We use Kaye Validator 2000 or Ellab data logger.
          Fermentor
          • We have experience with validation on smaller fermentors
          • We use Kaye Validator 2000
          Storages
          • We have experience with validation of large and small storages. We can also validate large warehouses where it is important to know the warehouse storage temperature if an item should be placed in the worst case location.
          • Depending on the size of the room, the Kaye Validator 2000 is used or Ellab logger
          Cool / climate
          • We have experience with validation of large and small cold storages
          • Depending on the size of the cold storage, the Kaye Validator 2000 or the Ellab logger is used

          Project Management

          When you as a customer need extra competencies to lead or support your projects, we enter into a close and confidential collaboration. Whether it is help needed with quality planning, financial sparring or coordination of subcontractors, we always put the customer at the center. It is the customer’s needs that come first from the start of the process until everything is working optimally and the project is handed over and taken into use. Subsequently, we are happy to make ourselves available to offer support and guidance.

          ON-SITE SUPPORT

          When our employees work on-site, they provide a broad experience and important ‘hands-on’ knowledge. This knowledge is not possible to obtain solely through certifications and education. The high professional level within our areas of competence is achieved ONLY through long-term, close, on-site collaboration in the individual companies’ production within calibration and thermal validation.

          Calibration

          • We work based on our own quality systems and working standards as well as the customer’s quality system and customer working standards/reference equipment.

          • We have experience with calibration of temperature, pressure, flow, dosage, conductivity, RPM.

          • We are always ready to expand our competencies to suit the customer’s needs.

          Thermal Validation

          • We work both on the basis of our own quality systems and working standards, as well as under the customer’s quality system and with the customer’s validation equipment.

          • We have experience with Kaye Validator 2000 and Ellab data logger.

          • We are always ready to expand our competencies to suit the customer’s needs.